mirror of
https://github.com/Lichee-Pi/u-boot.git
synced 2025-05-08 23:01:42 +08:00
cf3175bcd8
Since commit c0efc3140e75 ("ARM: uniphier: change CONFIG_SPL_PAD_TO
to 128KB"), the u-boot.bin should be burned at the offset 0x20000.
I missed to update README.uniphier in that commit. Now updating.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
# # Xilinx ZYNQ U-Boot # # (C) Copyright 2013 Xilinx, Inc. # # SPDX-License-Identifier: GPL-2.0+ # 1. About this This document describes the information about Xilinx Zynq U-Boot - like supported boards, ML status and TODO list. 2. Zynq boards Xilinx Zynq-7000 All Programmable SoCs enable extensive system level differentiation, integration, and flexibility through hardware, software, and I/O programmability. * zc702 (single qspi, gem0, mmc) [1] * zc706 (dual parallel qspi, gem0, mmc) [2] * zed (single qspi, gem0, mmc) [3] * microzed (single qspi, gem0, mmc) [4] * zc770 - zc770-xm010 (single qspi, gem0, mmc) - zc770-xm011 (8 or 16 bit nand) - zc770-xm012 (nor) - zc770-xm013 (dual parallel qspi, gem1) 3. Building ex. configure and build for zc702 board $ make zynq_zc702_config $ make 4. Bootmode Zynq has a facility to read the bootmode from the slcr bootmode register once user is setting through jumpers on the board - see page no:1546 on [5] All possible bootmode values are defined in Table 6-2:Boot_Mode MIO Pins on [5]. board_late_init() will read the bootmode values using slcr bootmode register at runtime and assign the modeboot variable to specific bootmode string which is intern used in autoboot. SLCR bootmode register Bit[3:0] values #define ZYNQ_BM_NOR 0x02 #define ZYNQ_BM_SD 0x05 #define ZYNQ_BM_JTAG 0x0 "modeboot" variable can assign any of "norboot", "sdboot" or "jtagboot" bootmode strings at runtime. 5. Mainline status - Added basic board configurations support. - Added zynq u-boot bsp code - arch/arm/cpu/armv7/zynq - Added zynq boards named - zc70x, zed, microzed, zc770_xm010, zc770_xm012, zc770_xm013 - Added zynq drivers: serial - drivers/serial/serial_zynq.c net - drivers/net/zynq_gem.c mmc - drivers/mmc/zynq_sdhci.c mmc - drivers/mmc/zynq_sdhci.c spi- drivers/spi/zynq_spi.c i2c - drivers/i2c/zynq_i2c.c - Done proper cleanups on board configurations - Added basic FDT support for zynq boards - d-cache support for zynq_gem.c 6. TODO - Add zynq boards support - zc770_xm011 - Add zynq qspi controller driver - Add zynq nand controller driver - Add FDT support on individual drivers [1] http://www.xilinx.com/products/boards-and-kits/EK-Z7-ZC702-G.htm [2] http://www.xilinx.com/products/boards-and-kits/EK-Z7-ZC706-G.htm [3] http://zedboard.org/product/zedboard [4] http://zedboard.org/product/microzed [5] http://www.xilinx.com/support/documentation/user_guides/ug585-Zynq-7000-TRM.pdf -- Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Sun Dec 15 14:52:41 IST 2013