poky-contrib/meta-yocto-bsp

              Yocto Project Hardware Reference BSPs README
              ============================================

This file gives details about using the Yocto Project hardware reference BSPs. The machines supported can be seen in the conf/machine/ directory and are listed below. There is one per supported hardware architecture and these are primarily used to validate that the Yocto Project works on the hardware arctectures of those machines.

If you are in doubt about using Poky/OpenEmbedded/Yocto Project with your hardware, consult the documentation for your board/device.

Support for additional devices is normally added by adding BSP layers to your configuration. For more information please see the Yocto Board Support Package (BSP) Developer's Guide - documentation source is in documentation/bspguide or download the PDF from:

https://docs.yoctoproject.org/

Note that these reference BSPs use the linux-yocto kernel and in general don't pull in binary module support for the platforms. This means some device functionality may be limited compared to a 'full' BSP which may be available.

Hardware Reference Boards

The following boards are supported by the meta-yocto-bsp layer:

• Texas Instruments Beaglebone (beaglebone-yocto)
• General 64-bit Arm SystemReady platforms (genericarm64)
• General IA platforms (genericx86 and genericx86-64)

For more information see the board's section below. The appropriate MACHINE variable value corresponding to the board is given in brackets.

Reference Board Maintenance and Contributions

Please refer to our contributor guide here: https://docs.yoctoproject.org/dev/contributor-guide/ for full details on how to submit changes.

As a quick guide, patches should be sent to poky@lists.yoctoproject.org The git command to do that would be:

 git send-email -M -1 --to poky@lists.yoctoproject.org

Send pull requests, patches, comments or questions about meta-yocto-bsp to poky@lists.yoctoproject.org

Maintainers: Kevin Hao kexin.hao@windriver.com Bruce Ashfield bruce.ashfield@gmail.com

Consumer Devices

The following consumer devices are supported by the meta-yocto-bsp layer:

• Arm-based SystemReady devices (genericarm64)
• Intel x86 based PCs and devices (genericx86 and genericx86-64)

For more information see the device's section below. The appropriate MACHINE variable value corresponding to the device is given in brackets.

                  Specific Hardware Documentation
                  ===============================

Intel x86 based PCs and devices (genericx86*)

The genericx86 and genericx86-64 MACHINE are tested on the following platforms:

Intel Xeon/Core i-Series:

• Intel NUC5 Series - ix-52xx Series SOC (Broadwell)
• Intel NUC6 Series - ix-62xx Series SOC (Skylake)
• Intel Shumway Xeon Server

Intel Atom platforms:

• MinnowBoard MAX - E3825 SOC (Bay Trail)
• MinnowBoard MAX - Turbot (ADI Engineering) - E3826 SOC (Bay Trail)
  • These boards can be either 32bot or 64bit modes depending on firmware
  • See minnowboard.org for details
• Intel Braswell SOC

and is likely to work on many unlisted Atom/Core/Xeon based devices. The MACHINE type supports ethernet, wifi, sound, and Intel/vesa graphics by default in addition to common PC input devices, busses, and so on.

Depending on the device, it can boot from a traditional hard-disk, a USB device, or over the network. Writing generated images to physical media is straightforward with a caveat for USB devices. The following examples assume the target boot device is /dev/sdb, be sure to verify this and use the correct device as the following commands are run as root and are not reversable.

USB Device:

1. Build a live image. This image type consists of a simple filesystem without a partition table, which is suitable for USB keys, and with the default setup for the genericx86 machine, this image type is built automatically for any image you build. For example:

   $ bitbake core-image-minimal

2. Use the "dd" utility to write the image to the raw block device. For example:

   dd if=core-image-minimal-genericx86.hddimg of=/dev/sdb

If the device fails to boot with "Boot error" displayed, or apparently stops just after the SYSLINUX version banner, it is likely the BIOS cannot understand the physical layout of the disk (or rather it expects a particular layout and cannot handle anything else). There are two possible solutions to this problem:

1. Change the BIOS USB Device setting to HDD mode. The label will vary by device, but the idea is to force BIOS to read the Cylinder/Head/Sector geometry from the device.

2. Use a ".wic" image with an EFI partition

   a) With a default grub-efi bootloader:

   dd if=core-image-minimal-genericx86-64.wic of=/dev/sdb

   b) Use systemd-boot instead

   • Build an image with EFI_PROVIDER="systemd-boot" then use the above dd command to write the image to a USB stick.

SystemReady Arm Platforms

The genericarm64 MACHINE is designed to work on standard SystemReady IR compliant boards with preinstalled firmware.

The genericarm64 MACHINE is currently tested on the following platforms:

• Texas Instruments BeaglePlay

The images built are EFI bootable disk images and can be written directly to a SD card for booting, for example.

Texas Instruments Beaglebone (beaglebone-yocto)

The Beaglebone is an ARM Cortex-A8 development board with USB, Ethernet, 2D/3D accelerated graphics, audio, serial, JTAG, and SD/MMC. The Black adds a faster CPU, more RAM, eMMC flash and a micro HDMI port. The beaglebone MACHINE is tested on the following platforms:

o Beaglebone Black A6 o Beaglebone A6 (the original "White" model)

The Beaglebone Black has eMMC, while the White does not. Pressing the USER/BOOT button when powering on will temporarily change the boot order. But for the sake of simplicity, these instructions assume you have erased the eMMC on the Black, so its boot behavior matches that of the White and boots off of SD card. To do this, issue the following commands from the u-boot prompt:

# mmc dev 1
# mmc erase 0 512

To further tailor these instructions for your board, please refer to the documentation at http://www.beagleboard.org/bone and http://www.beagleboard.org/black

From a Linux system with access to the image files perform the following steps:

1. Build an image. For example:

   $ bitbake core-image-minimal

2. Use the "dd" utility to write the image to the SD card. For example:

   dd if=core-image-minimal-beaglebone-yocto.wic of=/dev/sdb

3. Insert the SD card into the Beaglebone and boot the board.